Black PEEK Rod | Bearing Grade PEEK HPV Material
 MouseOver to Zoom.






You Might Also be Interested In

PEEK Sheet | Black PEEK Plastic

PEEK Unfilled Natural PolyEtherEtherKetone Tube

PEEK ROD | NATURAL GLASS 30%

PEEK SHEET | NATURAL

HOME > PEEK, BEARING GRADE

Black PEEK Rod | Bearing Grade PEEK HPV Material

Bearing grade carbon fiber reinforced thermoplastic rod



Get Your Online Pricing: Tips for measuring »

How To Measure and Cut-To-Size Policy [X]


Cut-To-Size Items are Non-Returnable!

As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade. Please review our full return and shipping policy here.

Measure Twice, Cut Once

Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.

How to Use a Measuring Tape

Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.

Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.

Features of a Measuring Tape: Sliding End Hook

The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).




Outside Diameter:

 inches
Length:

 ft
Quantity:



Total Price: $65.24

The minimum length for this rod is 5 feet. We have rounded the length.
Please call us at (916) 679-5146 for special length.

As low as $6/month with

Overview Specs & Uses Reviews Inquiry
PEKNEB RR - Overview

Bearing grade PEEK HPV is a high performance carbon fiber reinforced thermoplastic with excellent mechanical, slide, and wear properties. With the lowest coefficient of friction (COF) of all PEEK grades, it is best suited for bearing and wear applications and can run at high loads and speeds in hostile environments, including continuous exposure to hot water or steam. PEEK HPV is easier to machine than most PEEK grades and can be run dry or with an external lubricant. This rod is black in color.

PEEK HPV has a maximum continuous use temperature of 500?F. Its excellent chemical resistance allows PEEK HPV to work as a replacement for stainless steel or metal in hostile conditions. In general, PEEK has proven itself as a suitable replacement for other materials that cost up to 10 times more.



Features

[PDF Spec Sheet]

  • Lowest coefficient of friction of all PEEK grades
  • Good wear and slide properties
  • Excellent chemical resistance
  • Good heat deflection temperature
  • Resistant to superheated steam and hydrolysis
  • Great flame resistance - meets UL94 V-0 rating requirements
  • High creep resistance


Material Warnings

Material Warning WARNING: This product can expose you to chemicals including Carbon Black, CAS 1333-86-4, which are known to the State of California to cause cancer. For more information go to?www.P65Warnings.ca.gov.

WARNING: SHARP EDGES. Handle with care.
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.

Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored. Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.



Interstate Plastics Suppliers