As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade.Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
Sanitizing Acrylic and Polycarbonate Sheet [X]
Acrylic and Polycarbonate Sneeze Guards and like products require special care while cleaning and disinfecting. To maintain the optical clarity of sneeze guards and other acrylic or polycarbonate items, use an acrylic or polycarbonate safe cleaner like Novus Plastic Polish #1, Brillianize Plastic Cleaner, or a mild soap solution.
Please reference the following compatible cleaners when DISINFECTING acrylic and polycarbonate items. The use of commonly available commercial alcohol or ammonia-based disinfectants may cause crazing and damage.
G-10 / fr4 combines a woven glass fabric and an epoxy resin laminate (tg approximately 130-c) that contains bromine. G10 provides consistent quality and good electrical properties under dry and humid conditions, as well as high flexural, impact, and bond strength at room temperatures. This product is suitable for a variety of structural, high humidity, and electrical insulation applications, which include terminal boards, lapping carriers, and disc and microelectronics polishing. Np510a complies with the requirements of mil-i-24768/27, type GF.
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.
Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored.
Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.
I looked up local specialty plastics suppliers for the Austin, Texas area so I could source some G10/FR4 aka Garolite for use as a 3D Printer print surface aka bed plate and found their selection to be just what the Dr ordered..... and at a terrific price!!!!! I mean seriously a 305mm x 305mm x 3mm or 12" x 12" x 0.11811" is a great and I do mean GREAT deal. Matter of fact it was a far better deal to snatch up that particular 12" x 12" x 0.11811" than it was to buy it online and pay for the cost of shipping PLUS potential lead times that can easily run into a week or in some cases.... weeks! So yeah the only wish or request Ive got at his point is to have these G10/FR4 Sheets come in a variety of color if not multicolor.
Needed to replace some broken insulation bars in an electrical panel that were impossible to get from manufacturer. I fabbed them using this FR4 material and they turned out great. Excellent service by Interstate, cut to size and quick ship.
Received our shipment today and everything went smoothly. Will use them again.
really appreciated the prompt, efficient service with the order we placed ... they are a great company to work with!
High minimum, long lead time, slow shipping. Product is good.
A great find Interstate Plastics was for sourcing G10. Good price, good material.
Great bearing grade material. Fast shipping, good condition, good service.
Folks are knowledgeable about plastic properties and very responsive to customer enquiries. They are the go-to business on the East Bay for plastics.
Great customer service! Someone will always answer the phone and that speaks volumes. No automated phone BS.