G10 FR4 | PHENOLIC ROD | FR4 G10 ROD
 MouseOver to Zoom.






You Might Also be Interested In

G-10/FR4 GLASS EPOXY SHEET

G11 Phenolic Sheet | Glass Epoxy High Temperature Plastic

G11 PHENOLIC ROD | HEAT RESISTANT PLASTIC EPOXY GLASS LAMINATE

CE PHENOLIC | PHENOLIC ROD | CANVAS PHENOLIC

LE PHENOLIC | PHENOLIC ROD | LINEN PHENOLIC

HOME > PHENOLIC - GLASS

G10 FR4 | PHENOLIC ROD | FR4 G10 ROD

G10/FR4 Grade Phenolic Rod



Get Your Online Pricing: Tips for measuring »

How To Measure and Cut-To-Size Policy [X]


Cut-To-Size Items are Non-Returnable!

As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade. Please review our full return and shipping policy here.

Measure Twice, Cut Once

Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.

How to Use a Measuring Tape

Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.

Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.

Features of a Measuring Tape: Sliding End Hook

The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).

 

Total Price: $58.18


As low as $5/month with

Overview Specs & Uses Reviews Inquiry
PHEEG RR - Overview

G-10 / FR4 rods combine a woven glass fabric and an epoxy resin laminate (tg approximately 130?C) that contains bromine. G10 provides consistent quality and good electrical properties under dry and humid conditions, as well as high flexural, impact, and bond strength at room temperatures. This product is suitable for a variety of structural, high humidity, and electrical insulation applications, which include terminal boards, lapping carriers, and disc and microelectronics polishing. G10 / FR4 rods comply with the requirements of mil-i-24768/27, type GEE-F.



Features
  • High mechanical strength
  • Low water absorption
  • Low dissipation factor
  • Superb electrical properties
  • Can operate over a wide range of temperatures and humidities
  • mil-i-24768/27, type GEE-F


WARNING: SHARP EDGES. Handle with care.
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.

Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored. Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.



Interstate Plastics Suppliers