| MouseOver to Zoom.|
HOME > NYLON
NYLON TUBES | NATURAL CAST TUBULAR BAR
Polyamide | FDA Compliant
** WARNING, OD WILL BE SIGNIFICANTLY OVERSIZED, ID WILL BE SIGNIFICANTLY UNDERSIZED TO ALLOW FOR MACHINING TO LISTED DIMENSION **
5 stars based on 4 Review(s)
|Get Your Online Pricing:
Tips for measuring »
How To Measure and Cut-To-Size Policy [X]
Cut-To-Size Items are Non-Returnable!
As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade. Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
|As low as $104/month with |
Nylon is a tough, stable engineering thermoplastic with a high modulus of elasticity, high strength, good rigidity, dimensional stability, resistance to moisture, solvents and other chemicals. It performs significantly better than copolymers in toughness at extreme temperatures, fatigue endurance, and elongation at yield. Common applications include precision gears, bearings with close tolerances, electrical engineering insulators, snap fit assemblies, and parts operating in a hot water environment.
[PDF Spec Sheet]
NOTE: ALL TUBES COME SUFFICIENTLY OVERSIZED ON THE OD DIMENSION AND SUFFICIENTLY UNDERSIZED ON THE INSIDE DIMENSION TO ALLOW FOR MACHINING TO SIZE LISTED
- Low co-efficient of friction
- High modulus of elasticity
- High strength
- High rigidity and dimensional stability
- Resistant to chemicals and moisture
NEED A NYLON SAMPLE?
Thermoplastics Material Sample Pack
Friction Resistance Material Sample Pack
Tensile Strength Material Sample Pack
WARNING: This product can expose you to chemicals including N,N-Dimethylformamide, CAS 68-12-2, which are known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
WARNING: This product can expose you to chemicals including METHYLPYRROLIDONE, CAS 872-50-4, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.
Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored.
Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.