As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade.Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
Sanitizing Acrylic and Polycarbonate Sheet [X]
Acrylic and Polycarbonate Sneeze Guards and like products require special care while cleaning and disinfecting. To maintain the optical clarity of sneeze guards and other acrylic or polycarbonate items, use an acrylic or polycarbonate safe cleaner like Novus Plastic Polish #1, Brillianize Plastic Cleaner, or a mild soap solution.
Please reference the following compatible cleaners when DISINFECTING acrylic and polycarbonate items. The use of commonly available commercial alcohol or ammonia-based disinfectants may cause crazing and damage.
PTFE, also known under the brand name Teflon®1, is a soft fluoropolymer mechanical plastic with exceptional resistance to high temperatures, chemicals, corrosion and stress cracking.
PTFE features impressive heat, mechanical toughness, electrical and low friction properties, making it the material of choice for many high heat and low friction applications.
PTFE plastic is available in FDA approved, electrical, mechanical, glass-filled and bearing grades.
PTFE is soft and formable, often used for chemically resistant seals and gaskets. With strong electrical properties, PTFE is also used in many aerospace and computer applications. Glass-filled PTFE has enhanced strength and stiffness properties.
1Teflon® is a registered trademark of E. I. du Pont de Nemours and Company.
Material Warnings
WARNING: This product can expose you to chemicals including Tetrafluoroethylene, CAS 116-14-3, which are known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
WARNING: This product can expose you to chemicals including Tetrafluoroethylene, CAS 116-14-3, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.
Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored.
Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.
Bearings and bushings
Gears
Slide plates
Gaskets
Valve stem seals, valve seats
Chute liners
Pump parts
Cable insulation
Connector assemblies
Electrical sleeves
Semiconductor equipment
Scientific, medical equipment
Chemical resistant tubing
Shims
Oven plates
Non-stick and release coating
Date
Review
2016-11-14
My only complaint would be the lack of lack of communication and follow-up, but otherwise I am satisfied.
2016-07-22
Poorly shipped, the box looked as if it had been dropped. Luckily the sheet was not damaged and actually well protected. We're happy with the PTFE.
2015-10-13
Grade A material.
2015-08-17
Exceptional customer service from Interstate Plastics on this order! We got the size we needed and were able to add an extra overstocked sheet for a steal of a price!
2015-07-20
We use this for slide bearings. Interstate Plastics is easy to purchase from. Can't speak for their customer service as I've only ordered online. But they do send me confirmation emails. Great product great company.
4 stars based on 5 Review(s)
WARNING: This product can expose you to chemicals including Tetrafluoroethylene, CAS 116-14-3, which are known to the State of California to cause cancer. For more information go to 
WARNING: This product can expose you to chemicals including Tetrafluoroethylene, CAS 116-14-3, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to 
