As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade.Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
PTFE, or Polytetrafluoroethylene, is a fluoropolymer that is resistant to heat and chemicals. PTFE is inert to mostly all chemicals and is considered the slipperiest material in existence. It has an extremely low coefficient of friction, and is used as a coating on cookware, gaskets, seals, and hoses. It is unaffected by virtually all acids and caustics, functioning in environments up to 500?F, and as low as -350?F. Virgin PTFE is approved by the Food and Drug Administration for use in the food, beverage, cosmetics and pharmaceutical industries.
Also known under the brand name Teflon®, PTFE is a soft fluoropolymer mechanical plastic with exceptional resistance to high temperatures, chemicals, corrosion and stress cracking. PTFE features impressive heat, mechanical toughness, electrical and low friction properties, making it the material of choice for many high heat and low friction applications. PTFE plastic is available in FDA approved, electrical, mechanical, glass-filled and bearing grades.
Bearings and bushings
Valve stem seals, valve seats
Scientific, medical equipment
Chemical resistant tubing
Non-stick and release coating
Extremely low co-efficient of friction
Excellent chemical and weather resistance
Great electrical insulator
Great thermal stability and operating temperature range
WARNING: This product can expose you to chemicals including Tetrafluoroethylene, CAS 116-14-3, which are known to the State of California to cause cancer. For more information go to?www.P65Warnings.ca.gov.
WARNING: This product can expose you to chemicals including Tetrafluoroethylene, CAS 116-14-3, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to?www.P65Warnings.ca.gov.
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.
Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored.
Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.
PTFE (Virgin) is approved for food use by the FDA.
Home: non-stick pots, pans, utensils, nail polish, curling irons,carpet and fabric protection coatings
Automotive: windshield wiper blades
Industrial: hoses, tubing and pipe lining, high temperature, general purpose, gaskets, slide bearings, dough rollers, insulators,valve stem seals, valve seats, extrusion nozzles, electrical sleeving, bushes, o-rings, and chute liners
Thanks for a smooth order! I should note that all was well and intact but the cardboard that was protecting it came pretty ripped up. Not sure if that was Interstate Plastics or the shipping company. Either way Interstate was great, very helpful
Superb quality product.
A little frustration with shipping costs, but a good overall satisfaction with customer service and the quality of the rod.
A good choise for us for bearing material and easy to work with company
Ordered Teflon sheet and rod, customer service helped me pick the right grade, shipped quickly, and received as described.
We did weeks of research looking for the right PTFE (Teflon) supplier. On the website I found my the PTFE price that couldn't be beat. I've had the material for four months and have had no problems. Delivery was on time and goods arrived undamaged. Great customer service. I will definitely be buying again.
Solid product. Undamaged Teflon rod, shipped on time.
Write Your Own Review
PTFE ROD | VIRGIN POLYTETRAFLUOROETHYLENE Questions?