As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade.Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
Sanitizing Acrylic and Polycarbonate Sheet [X]
Acrylic and Polycarbonate Sneeze Guards and like products require special care while cleaning and disinfecting. To maintain the optical clarity of sneeze guards and other acrylic or polycarbonate items, use an acrylic or polycarbonate safe cleaner like Novus Plastic Polish #1, Brillianize Plastic Cleaner, or a mild soap solution.
Please reference the following compatible cleaners when DISINFECTING acrylic and polycarbonate items. The use of commonly available commercial alcohol or ammonia-based disinfectants may cause crazing and damage.
Interstate Plastics' line of UHMW pressure sensitive adhesive backed tapes offer excellent abrasion resistance, low coefficient of friction, high impact strength and high performance properties people have come to expect from UHMW. By providing this exceptional material with an adhesive backing, installation time and costs are significantly reduced. No need for bolts or fasteners, no need to countersink.
DuraSurf ETA also reduces scrap by 75%. When a standard 1/4" thick sheet of UHMW is installed using the traditional mechanical fastening method, 3/16" of the material is lost to the bolt head. This leaves only a 1/16" usable wear surface. You can achieve the same result with a 1/16" DuraSurf ETA tape product and eliminate 80% of the time and cost associated with traditional installation methods. Interstate Plastics offers a wide range of both rubber and acrylic based adhesive systems to meet virtually any application requirement.
DON'T SEE THE SIZE YOU'RE LOOKING FOR? CALL 888-768-5759. Available thicknesses: 005" (.125 mm), .010" (.25 mm), .015"(.38 mm), .020" (.5 mm), .031" (.75 mm), .040" (1 mm), .050" (1.3 mm), .062" (1.57 mm), .080" (2 mm) .093" (2.35 mm), .100" (2.5 mm), .125" (3.17 mm) Available widths: All dimensions between 1/4" (6.35 mm) and 24" (610 mm)
Features
Excellent abrasion and wear resistance
Very high impact strength
Meets FDA and USDA guidelines
No moisture absorption
Self-lubricating - no need for oils or lubricants
Excellent noise abatement properties
Chemical resistance and corrosion resistant
Maintains performance and properties at -30-C
Meets ASTM-D-4020-81
Low coefficient of friction
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.
Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored.
Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.
The incredible durability and versatility of DuraSurf makes it a favorite among engineers and designers in nearly every industry worldwide. UHMW-PE's long molecular chain gives it a host of exceptional attributes: high abrasion resistance, low coefficient friction and unparalleled impact resistance, even in cryogenic environments. It is extremely stable in temperatures ranging from 220-F, down to cryogenic lows. It is an excellent electric insulator, and is easily machined, punched, sawed, and drilled.
Physical Properties
Specification
Unit/Standard
Value
Density
gm/cc
0.93
Tensile strength at break
Mpa(psi)
44-53
Elongation at break
%
60-466
Friction Coefficient
Static
.16
Hardness Shore "D"
ASTM-D256
65
Water Absorption
%
Nil
Write Your Own Review
UHMW DURASURF ETA PRESSURE-SENSITIVE TAPE Questions?