As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade.Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
Sanitizing Acrylic and Polycarbonate Sheet [X]
Acrylic and Polycarbonate Sneeze Guards and like products require special care while cleaning and disinfecting. To maintain the optical clarity of sneeze guards and other acrylic or polycarbonate items, use an acrylic or polycarbonate safe cleaner like Novus Plastic Polish #1, Brillianize Plastic Cleaner, or a mild soap solution.
Please reference the following compatible cleaners when DISINFECTING acrylic and polycarbonate items. The use of commonly available commercial alcohol or ammonia-based disinfectants may cause crazing and damage.
WE OFFER CUSTOM PROFILES AND STRIPS: Submit your specifications using the "Inquiry" tab on this page or use our custom quote form to send us a diagram and our representatives will provide you with a custom quote. You can also call us for more information at 888-768-5759.
Rustication strips create an architectural reveal in walls or other concrete elements. Manufactured from rigid HDPE or UHMW, our rustication strips are reusable, maintain a smooth and even reveal, and are ideal for eliminating seams on form liner applications. UHMW is used for harder to release reveals, and it is a much tougher product than HDPE. HDPE is used for easy to release reveals as it is more cost-effective.
Tilt-up wall construction is a widely-used method of constructing walls for buildings. In this method reveal strips and chamfer strips are used to add beauty and functionality to concrete walls by creating desired voids in a finished concrete wall or other concrete object. A tilt-up wall is typically constructed by pouring a concrete slab within forms horizontally, on the ground, then tilting up the cured concrete slab vertically to act as a wall.
Features
Extremely low moisture absorption
Very low coefficient of friction
Self-lubricating
Highly resistant to wear and abrasion
Easy to fabricate and machine with common shop and woodworking tools
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.
Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored.
Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.
WE OFFER CUSTOM PROFILES AND STRIPS: Submit your drawings using the "Inquiry" tab on this page and our representatives will provide you with a custom quote. You can also call us for more information at 888-768-5759.
