As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade.Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
Sanitizing Acrylic and Polycarbonate Sheet [X]
Acrylic and Polycarbonate Sneeze Guards and like products require special care while cleaning and disinfecting. To maintain the optical clarity of sneeze guards and other acrylic or polycarbonate items, use an acrylic or polycarbonate safe cleaner like Novus Plastic Polish #1, Brillianize Plastic Cleaner, or a mild soap solution.
Please reference the following compatible cleaners when DISINFECTING acrylic and polycarbonate items. The use of commonly available commercial alcohol or ammonia-based disinfectants may cause crazing and damage.
UV-Stabilized & Moisture-Resistant HDPE for Marine Environments
White HDPE Marine Board was created to withstand the demands of marine and outdoor environments. A resilient, lightweight thermoplastic, this material is manufactured with UV stabilizers to provide a reliable material for projects subjected to sun, moisture, and saltwater exposure.
White Marine Board is an economical replacement for standard wood or metal components. Designed to resist splintering, rotting, and delamination, it eliminates the need for regular refinishing or painting. Its stabilized HDPE formulation makes it an efficient choice for both commercial and recreational marine builds.
Marine Board HDPE offers excellent durability in marine applications. Choose this material if your project needs:
Salt Water & Moisture Resistance:
Low moisture absorption helps prevent the swelling, rotting, and delamination associated with wood-based marine materials.
UV-Stabilized Longevity:
Environmentally stabilized to help slow color and property degradation during prolonged outdoor exposure.
Decorative Textured Finish:
Features a decorative, textured surface that helps make everyday scuffs and handling marks less noticeable.
Chemical Resistance & Cleanability:
Highly resistant to a broad spectrum of chemicals, acids, and alcohols, which makes it easy to clean and maintain.
Cost-Effective Utility:
Delivers the core performance characteristics of marine polyethylenes at a competitive price point for budget-conscious fabrications.
Marine Board vs. King StarBoard®: Which Do You Need?
While both materials utilize a polyethylene base optimized for outdoor exposure, they cater to different operational demands:
Choose White HDPE Marine Board (This Sheet) when you need an economical, UV-stabilized HDPE sheet for general marine cabinetry, hatches, trim, storage components, and other non-structural fabrications.
Choose King StarBoard® if your application calls for a recognized marine-grade HDPE brand, specific color matching, or specialized variants such as anti-skid textures (StarBoard® A/S) or lightweight cellular cores (StarBoard® XL).
Fabrication & Machining
HDPE Marine Board is a fabrication-friendly material and can be easily cut, routed, and drilled with standard woodworking equipment. While it is thermoformable, precise temperature controls are necessary due to its high thermal expansion. Note: HDPE has low surface energy and is difficult to reliably bond with standard adhesives; use mechanical fasteners, coarse threads, or plastic welding for optimal holding power.
Interstate Plastics Marine Board is a very light and extremely tough, chemically resistant plastic. It does not absorb water and has good sliding abrasion resistance in addition to being self-lubricating.
Acid, odor, moisture and mildew resistant
Extremely easy to machine with common woodworking tools
Excellent chemical resistance to acids, alcohols and bases
Excellent long-term durability
Great weather resistance : will not delaminate, rot, chip or swell
Abrasion and wear resistances
Thermoformable
Good flexibility and toughness
Cost effective compared to other marine solutions
Low-maintenance
UV-stabilized
FDA approved in certain grades
High impact and tensile strength
Excellent energy absorption
Decorative, textured surface retains original color and doesn't show wear, dirt or scratches
Gloss finish
Easy to clean
Handling: Cut sheets may have sharp edges. We recommend wearing protective gloves when unpacking and handling this material to ensure safety.
Suitability: We take pride in the quality of our materials as they leave our facility. However, because every project is unique, we cannot account for how materials are modified, stored, or used after delivery. Please perform the necessary tests to ensure this material is right for your specific application and end-use conditions.
HDPWEM SH
Technical Performance
This UV-stabilized, white-pigmented HDPE is specifically engineered for outdoor and marine applications requiring a combination of very low moisture absorption, chemical resistance, and durable impact strength.
Moisture Resistance:
Low water absorption helps prevent moisture-related swelling and eliminates the risk of rotting or delamination associated with wood-based materials.
Environmental Stability:
UV-stabilized formula protects the base polymer from degradation and helps resist premature fading, brittleness, and property degradation during outdoor use.
Impact Resistance:
Provides the toughness needed for hatches, cabinetry, trim, storage components, and other properly supported marine fabrications.
Key Properties
Easy to Machine:
Can be quickly and precisely fabricated using standard, common woodworking tools and shop machinery.
Chemical Resistance:
Highly resistant to acids, alcohols, bases, and common marine cleaning agents, protecting against chemical staining or degradation.
Low Maintenance:
The solid white color extends through the entire sheet and requires no sealing, painting, or regular aesthetic refinishing.
Heat Formable:
Can be formed into gradual curves with proper heat control, fixturing, and allowance for thermal expansion.
Marine Utility Surfaces: Bait-station components, utility tables, and washdown-area panels.
Outdoor Fabrication: Furniture components, equipment panels, signs, and non-structural fixtures exposed to moisture and sunlight.
Engineering Limitations & Alternatives
While White HDPE Marine Board is designed to provide efficient moisture and weather resistance, specific applications may require alternative engineering materials:
Tight Machining Tolerances: Due to a relatively high coefficient of thermal expansion, HDPE expands and contracts significantly with temperature swings, making it difficult to maintain extremely tight tolerances. Better Alternative: For precision-machined industrial parts requiring strict dimensional stability, consider Acetal.
Dedicated Anti-Skid Surfaces: The standard textured finish provides basic scuff resistance but is not certified as a dedicated non-skid walking surface for high-angle marine decks. Better Alternative: For marine steps, walkways, and other safety-focused walking surfaces, consider premium King StarBoard® A/S.