Nylon Oil-Filled Discs | Cast Nylon MD Round Stock
 MouseOver to Zoom.






You Might Also be Interested In

Interstate Advanced Materials Membership

Nylon Discs | Cast Nylon 6 Round Stock

Gray MD Nylon Sheet | Cast Nylon 6 MD

HOME > NYLON

Nylon Oil-Filled Discs | Cast Nylon MD Round Stock

MoS2 filled cast nylon discs for wear applications



Get Your Online Pricing: Tips for measuring »

How To Measure and Cut-To-Size Policy [X]


Cut-To-Size Items are Non-Returnable!

As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade. Please review our full return and shipping policy here.

Measure Twice, Cut Once

Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.

How to Use a Measuring Tape

Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.

Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.

Features of a Measuring Tape: Sliding End Hook

The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).

 

Total Price: $30.57


As low as $3/month with

Overview Specs & Uses Reviews Inquiry
NYLBCM DISC - Overview

Nylon MD is a combination of cast nylon and molybdenum disulfide (MoS2), a dry lubricant used in metal applications. The result of this combination is a material capable of bearing heavier loads than standard nylon. MoS2 reinforces nylon's strength without compromising its excellent impact resistance or electrical characteristics and imbues nylon with additional lubricity. The extra lubricity gives Nylon MD a low coefficient of friction, good wear resistance, and the ability to operate with little to no external lubrication. It is ideal for applications where external lubrication is too difficult or not possible.

Nylon MD discs have increased longevity due to their lubricity, making them a cost-effective choice compared to similar materials. Lightweight and tough, Nylon MD discs are used to replace metallic parts, including gears, wear strips, bearings, sprockets, and custom parts.



Features
  • Light weight
  • Good mechanical and electrical properties
  • Excellent strength and impact resistance - capable of bearing heavier loads than standard nylon
  • Built-in MoS2 dry lubricant - low coefficient of friction
  • Great wear resistance
  • Can function in environments where external lubrication is impossible
  • Increased part life - cost-effective
  • Resistant to chemicals, moisture


Material Warnings

Material Warning WARNING: This product can expose you to chemicals including N,N-Dimethylformamide, CAS 68-12-2, which are known to the State of California to cause cancer. For more information go to?www.P65Warnings.ca.gov.

WARNING: This product can expose you to chemicals including METHYLPYRROLIDONE, CAS 872-50-4, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to?www.P65Warnings.ca.gov.

WARNING: SHARP EDGES. Handle with care.
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.

Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored. Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.



Interstate Plastics Suppliers