As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade.Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
Sanitizing Acrylic and Polycarbonate Sheet [X]
Acrylic and Polycarbonate Sneeze Guards and like products require special care while cleaning and disinfecting. To maintain the optical clarity of sneeze guards and other acrylic or polycarbonate items, use an acrylic or polycarbonate safe cleaner like Novus Plastic Polish #1, Brillianize Plastic Cleaner, or a mild soap solution.
Please reference the following compatible cleaners when DISINFECTING acrylic and polycarbonate items. The use of commonly available commercial alcohol or ammonia-based disinfectants may cause crazing and damage.
Renovo-MPC™ clear polycarbonate is a tough sheet material with outstanding strength, stiffness, and impact resistance. Made from reclaimed post-consumer and industrial polycarbonate, Renovo-MPC™ is fully sustainable while retaining the properties of general-purpose extruded polycarbonate, including its outstanding optical clarity, high light transmission, and low haze. Renovo-MPC™ is a closed loop material that is lightweight, shatter-resistant, and has a higher impact resistance than glass. Like general-purpose polycarbonate, this material may be thermoformed, sawed, routed, drilled, and is hot and cold bendable.
Renovo-MPC™ is manufactured in the U.S. and may be used toward LEED Materials and Resources credits in some applications.
Closed loop post-consumer polycarbonate that retains all of general-purpose polycarbonate's properties
Excellent optical clarity
May be routed, drilled, and sawed
Cold and hot bendable
Usable toward LEED credits in some applications
Made in the U.S.A.
WARNING: This product can expose you to chemicals including Bisphenol A, CAS 80-05-7 , which are known to the State of California to cause birth defects or other reproductive harm. For more information go to�www.P65Warnings.ca.gov.
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.
Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored.
Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.
Renovo-MPC™ is a fully sustainable closed loop polycarbonate sheet. It may be used in many of the same applications as standard polycarbonate, including:
Replacement for glass
Indoor and outdoor signage
Flat and curved glazing
Other applications where optical clarity is required, but glass would pose a high risk