As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade.Please review our full return and shipping policy here.
Measure Twice, Cut Once
Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.
How to Use a Measuring Tape
Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.
Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.
Features of a Measuring Tape: Sliding End Hook
The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).
Sanitizing Acrylic and Polycarbonate Sheet [X]
Acrylic and Polycarbonate Sneeze Guards and like products require special care while cleaning and disinfecting. To maintain the optical clarity of sneeze guards and other acrylic or polycarbonate items, use an acrylic or polycarbonate safe cleaner like Novus Plastic Polish #1, Brillianize Plastic Cleaner, or a mild soap solution.
Please reference the following compatible cleaners when DISINFECTING acrylic and polycarbonate items. The use of commonly available commercial alcohol or ammonia-based disinfectants may cause crazing and damage.
Polyvinyl chloride, or PVC for short, is one of the world's most widely used plastics for its extreme versatility. Most PVC produced goes into building and construction applications such pipe, siding, and window profiles. PVC has a great resistance to oils and a low permeability to gases. It is ideally suited for applications where maximum chemical resistance is necessary. Sheets can be welded to produce tanks, trays and troughs. Packaging is another major market for PVC plastic. Rigid PVC is blown into bottles and made into sheet for thermoforming boxes and blister packs. Flexible compounds are made into food wrap. Other markets for PVC plastics include wire and cable coating, flooring, garden hose, and toys.
Gray PVC conforms to ASTM d-1784-95 class 12454-b (formerly type i grade 1) and is manufactured without the use of plasticizers or fillers. It can be used in self supporting construction up to 140?F (depending on chemistry). It exhibits excellent fire ratings (ul-94v-0) and has a flame spread under 20 per ASTM-e-84.
Note: PVC is an industrial grade plastic with no protective masking. Scratches and scuffs on sheets are considered acceptable and are not a valid reason for returning this material.
WARNING: This product can expose you to chemicals including Polyvinyl Chloride, CAS 9002-86, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov .
Warning: This product may have sharp edges and points. Contact may result in injury. Handle with care.
Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored.
Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.
Roughly half of the world's polyvinyl chloride resin manufactured annually is used for producing pipes for municipal and industrial applications:
Pipes: sanitary, sewer, water supply, reinforcement, drainage, gutters, downspouts
Electrical cable insulation
Painted wood substitute
Window frames
Leather-like substitute in clothing
Date
Review
2016-04-19
Super super cheap and high quality! Great service, thank you!
2016-01-26
outstanding customer service. they will get my business every time our company needs plastic products.
2014-04-18
For years I have gotten excellent material from Interstate Plastics and am always happy with the level of customer service I receive on the phone. I love the new online ordering system!
2014-03-11
Good quality plastic, the cut to size dimensions are spot on. I have used it and never had troubles Great price too! I received a cheap, warped piece of PVC from a competitor (I will not name here) that did not fit my specs and did not hold up for long. Interstate has great tolerances on their cuts.
2014-02-17
Quite pleased with the team over at Interstate Plastics. We are a long time purchaser of PVC and look forward to a continuing relationship with IP for all of our plastic needs. These guys truly go above and beyond.
2013-10-11
I wouldn't go up to 140 degrees, but this can take some heat. Good price, actually great price, reasonable shipping. No damage on arrival.
2013-10-08
Thanks for helping me! The gray PVC sheet cut easily and works perfectly for a part I have welded onto my airsoft gun design.
2013-09-11
Thanks so much for your prompt response; Interstate Plastics has really been great to work with.
2012-10-08
Thanks for taking care of me!
Write Your Own Review
Gray PVC Sheet | Rigid PVC Type 1 Sheet Questions?