Plastic experts are here to assist you 8AM-5PM PST Mon-Fri

 MouseOver to Zoom.



Flame resistant material for semiconductor clean rooms and electrical equipment.

Get Your Online Pricing: Sanitizing Acrylic and Polycarbonate »
Tips for measuring & cut-to-size policy »

How To Measure and Cut-To-Size Policy [X]

Cut-To-Size Items are Non-Returnable!

As per our Shipping and Returns Policy, custom cuts and fabricated parts are non-returnable. If you need an over- or undersized item, note it under "Comments" during Checkout. Cut-to-size orders have an acceptable cut tolerance of 1/8" (0.125"), so clarify if the adjustment is to be made on the (+) or (-) side of the saw blade. Please review our full return and shipping policy here.

Measure Twice, Cut Once

Since custom cuts and fabricated parts are non-refundable, be very careful while measuring your dimensions. As each cut is nominal, even the slightest miscalculation could be costly.

How to Use a Measuring Tape

Extend your tape measure several inches to find the 1 and 2 inch markers. In between the inch markers you’ll find 16 equally spaced tick marks.

Measure by counting the increments beyond the nearest inch. As the increments decrease, so does the length of the mark. For example, 1/2" has a bigger mark than 1/4" which has a bigger mark than 1/8". The smallest mark follows at 1/16". Please be aware that some measuring tapes may have even smaller increments.

Features of a Measuring Tape: Sliding End Hook

The sliding end hook is designed for two different types of measurements. An outside measurement (where the hook of the tape hangs over an edge), requires the hook to slide out a bit to account for the thickness of the material. When making an inside measurement (where the hook will push up against a surface), the clip slides in, again, accounting for its thickness. The measuring tape self-adjusts to guarantee an accurate measurement (as far as the tape is concerned).

Sanitizing Acrylic and Polycarbonate Sheet [X]

Acrylic and Polycarbonate Sneeze Guards and like products require special care while cleaning and disinfecting. To maintain the optical clarity of sneeze guards and other acrylic or polycarbonate items, use an acrylic or polycarbonate safe cleaner like Novus Plastic Polish #1, Brillianize Plastic Cleaner, or a mild soap solution.

Please reference the following compatible cleaners when DISINFECTING acrylic and polycarbonate items. The use of commonly available commercial alcohol or ammonia-based disinfectants may cause crazing and damage.

Compatible Polycarbonate Disinfectants:

• sBioMed Steriplex SD
• Safetec Surface Wipes
• Contec Healthcare Perodox RTU
• Contec Healthcare PS-911 EB Prostat Sterile Wipes

Compatible Acrylic Disinfectants:

• Pharmacy Grade Hydrogen Peroxide
• Household Bleach
• Isopropyl Alcohol (Water Diluted to 30% Strength)

[Download as a PDF]

PVDF Kynar 740 Sheet .125" x 48" x 96"$1,039.00
PVDF Kynar 740 Sheet .25" x 48" x 96"$2,079.00
PVDF Kynar 740 Sheet .375" x 48" x 96"$3,125.00
PVDF Kynar 740 Sheet .5" x 48" x 96"$4,150.00
PVDF Kynar 740 Sheet .75" x 48" x 96"$6,695.00
PVDF Kynar 740 Sheet 1" x 48" x 96"$8,925.00
PVDF Kynar 740 Sheet 1.25" x 48" x 96"$11,995.00
PVDF Kynar 740 Sheet 1.5" x 48" x 96"$14,395.00
PVDF Kynar 740 Sheet 2" x 48" x 96"$18,895.00

Total Price: $1,039.00


Overview Specs & Uses Reviews Inquiry
PVDNE7 SH - Overview

PVDF Kynar 740 sheet fulfills the requirements of FM 4910 and UL 94 V-0 flammability tests for semiconductor clean rooms and electrical equipment. This engineering thermoplastic has exceptional resistance to acids and ultra-pure water. PVDF Kynar 740 sheet has higher stiffness and temperature resistance versus PVDF-C 2850, but slightly lower impact resistance and flexibility. Both perform well in chemical environments and are exceptionally resistant to concentrated acids and ultra-pure water, in a wide temperature range.

PVDF Kynar 740 sheet has been found exceptionally useful for the following applications:

  • Semiconductor process tanks and components
  • Chemical process tanks and components
  • Wetted parts (component in direct contact with fluid under pressure)
  • Fume hoods and ducting
  • DI water and acid etch systems
  • Scientific and laboratory equipment

  • FM 4910 compliant
  • Meets UL 94 V-0 criteria
  • Service temperatures up to 250°F (121°C)
  • Exceptional UPW (ultra-pure water) and acid resistance
  • High gloss sheet surface
  • Welds to PVC CRP-1
  • High purity/low extractables
  • High abrasion, chemical, UV, and radiation resistance
  • Low permeability

Material Warnings

 WARNING: This product can expose you to chemicals including Tetrafluoroethylene, CAS 116-14-3, which are known to the State of California to cause cancer. For more information go to

WARNING: This product can expose you to chemicals including Tetrafluoroethylene, CAS 116-14-3, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to

Disclaimer: Interstate Plastics makes no representations about any of its products that are modified in any way after they leave its possession, nor do its representations apply when any of its products are improperly used or stored. Each customer of Interstate Plastics bears full responsibility for making its own determination as to the suitability of each material, product, recommendation or advice provided by Interstate Plastics. Each customer of Interstate Plastics must identify and perform all tests and analyses necessary to assure that its finished parts incorporating materials from Interstate Plastics will be safe and suitable for use under end-use conditions.

Interstate Plastics Suppliers